Wednesday, June 16, 2021

Inspiration Wednesday over at Heartfelt Creations,

 today I have for you a pretty card with a butterfly and climbing clematises. All the details are below.


 HCFB1-5006 3D Climbing Clematis Shaping Mold

HCDP1-2128 Climbing Clematis paper pad

HCPC-3954 Clematis cling stamp

HCD1-7355 Clematis die set

HCPC-3955 Clematis Spray cling stamp set

HCD1-7356 Clematis Spray die set

HCPC-3951 Large Floral Butterfly cling stamp set

HCD1-7352 Large Floral Butterfly die set

HCPC-3848 Cheerful Note Sentiments cling stamp set

HCD2-7337 Tear Drop Lattice Gateway die set

HCST1-401 Deluxe Flower Shaping Kit

HCPP1-475 Deluxe Flower Shaping Paper Pad

159723 Designer Dries Clear Adhesive

352854 Metal Tip For Adhesive Bottles

DMCT4185 Groove Golf Tool Set

359848 Spellbinders Tool N’ One

RAHT Heat It Craft Tool

409311 Color In Water Brush-fine

359760 Embossing powder-Gold

DDOT 3D Double Sided Foam Dots

173842  Scor-Pal Measuring & Scoring Board

409311 Color in Watercolor Brush-fine

901 Krystallos Shard Glass

 OTHER PRODUCTS USED: Coloring:-Glimmer Mist: Olive Vine, Cherub Pink. Other: Double sided tape, Double sided foam Tape, Versa-mark, Hot glue Gun, Fussy cutting scissors, Ruler

INSTRUCTIONS: The size of this tent fold card is 6  3 / 4 “ x 8  1 / 2 “

Make a card base to the above measurements from the white card stock then make the card front from the design paper sheet 1B a little smaller than the card base., adhere this to the card base. Taking the same design paper and the gateway frame die, die cut the frame. Adhere this to the card front using the 3D foam tape.Taking the butterfly die set, find the outer die then die cut this shape from the design paper sheet 1B. Adhere to the card front (gateway frame) on a slant using a few layers of 3D foam tape or the 3D circle dots. The tape is placed at the center of the butterfly so the tips of the wings remain free. Using the white card stock, the butterfly stamp, matching die and the lace inner die, prepare the butterfly. Stamp with the gold embossing powder then color this with the Cherub Pink and the English Ivy glimmer mist by spraying or bringing the ink onto the image with the water coloring brush. When dry die cut using the matching die. Do the same again but you will only need the butterflies body. Die cut the inner butterfly wings twice from the white card stock. Curl the wings up so they will look like they are fluttering when adhered to the card front. Adhere the complete stamped butterfly to the butterfly base at the body so the wings can be raised by curling them up with your fingers. Adhere the two lacy butterfly wings also at the body. Adhere the extra body part of the butterfly to the existing body part using 3D foam tape.Make x 4 large flower curved boarders and  5 x large, 4 x medium and 9 x small sized clematis flowers by stamping with gold embossing powder onto white card stock and coloring with the glimmer mists. Die cut all with the matching dies. Bring shape to the flowers by using the matching molds and shaping tools. Arrange the curved boarders to the top sides of the gateway frame. Arrange the flowers on to the card front as seen in the photo then adhere with a hot glue gun. Adhere 2 small flowers together to the middle of the butterflies body. Apply clear drying adhesive to the flower centers then sprinkle the shard glass into the adhesive. When dry tap away any excess shaved glass.To finish the card, make the sentiment banner by stamping the sentiment with the gold embossing powder and fussy cut the ends. Give the banner a curl with your fingers so it has a curve in the middle of the banner.  Adhere to the foot of the card front under the gateway frame.

For a printout of the instructions, visit HERE

;Have a happy scrappy inky day.